PCI and PCIe Expansion Slots: Architecture and Performance
A+ Core 1 · Hardware · Bởi Super Admin
Explore the differences between PCI and PCIe expansion slots, including data rates, lane configurations, and compatibility considerations for modern systems.
Understanding PCI Expansion Technology
The most visible parts of any motherboard are the connectors for internal expansion cards, also called expansion slots. These small plastic slots, usually from 1 to 6 inches long and approximately 1/2 inch wide, are used to install various devices in the computer to expand its capabilities. Expansion devices that might be installed in these slots include video, network, sound, and disk interface cards. The two main types of expansion slots used in computers today are PCI and PCIe.
Peripheral Component Interconnect (PCI) slots are now considered an old technology, but many motherboards in use today still contain 32-bit PCI slots. They are easily recognizable because they are only around 3 inches long and classically white, although modern boards take liberties with the color. PCI slots became extremely popular with the advent of Pentium-class processors in the mid-1990s. PCI expansion buses operate at 33 MHz or 66 MHz (version 2.1) over a 32-bit (4-byte) channel, resulting in data rates of 133 MBps and 266 MBps, respectively, with 133 MBps being the most common. PCI is a shared-bus topology, so mixing 33 MHz and 66 MHz adapters in a 66 MHz system will slow all adapters to 33 MHz.
<img src="/question_assets/220-1201/sg_c01f003.png" alt="PCI expansion slots"/>
<figcaption>PCI expansion slots</figcaption>
The image above shows several PCI expansion slots, with a shorter 5V 32-bit slot in the foreground and longer 3.3V 64-bit slots visible. PCI slots and adapters are manufactured in 3.3V and 5V versions, with universal adapters keyed to fit in slots based on either of the two voltages. The notch in the card edge of the common 5V slots and adapters is oriented toward the front of the motherboard, while the notch in the 3.3V adapters is toward the rear.
PCIe Serial Architecture and Lane Configuration
PCI Express (PCIe) is the most common expansion slot architecture used on motherboards today. It was designed to be a replacement for PCI as well as an older video card standard called accelerated graphics port (AGP). PCIe has the advantage of being faster than AGP while maintaining the flexibility of PCI. PCIe has no plug compatibility with either AGP or PCI, though some modern PCIe motherboards can be found with regular PCI slots for backward compatibility.
PCIe is casually referred to as a bus architecture to simplify its comparison with other bus technologies, but it actually uses a switching component with point-to-point connections to slots. This gives each component full use of the corresponding bandwidth and makes connections faster. Unlike other expansion buses which have parallel architectures, PCIe is a serial technology, striping data packets across multiple serial paths to achieve higher data rates. PCIe uses the concept of lanes, which are the switched point-to-point signal paths between any two PCIe components. Each lane comprises a separate pair of wires for both directions of traffic.
Link Widths and Performance Standards
There are seven different link widths supported by PCIe, designated x1, x2, x4, x8, x12, x16, and x32, with x1, x4, and x16 being the most common. A slot that supports a particular link width is of a physical size related to that width because the width is based on the number of lanes supported. As a result, a x8 slot is longer than a x1 slot but shorter than a x16 slot. Every PCIe slot has a 22-pin portion in common toward the rear of the motherboard, which comprises mostly voltage and ground leads.
<img src="/question_assets/220-1201/sg_c01f004.png" alt="PCIe expansion slots"/>
<figcaption>PCIe expansion slots</figcaption>
The image above shows PCIe expansion slots from top to bottom: PCIe x4, PCIe x16, PCIe x1, PCIe x16, and PCI slots. The oldest version, 1.X, was released in 2003, running at 250 MBps per direction, or 500 Mbps bidirectionally. Combining lanes results in a linear multiplication of these rates. For example, a PCIe 1.1 x16 slot is capable of 4 GBps of throughput in each direction, which is 16 times the 250 MBps x1 rate. Each subsequent PCIe specification doubles this throughput. PCIe 6.0 has a single-lane data rate of 8 GBps, for a total x16 bidirectional bandwidth of 256 GBps. PCIe versions are backward compatible, so a PCIe 5.0 x1 card will fit into a PCIe 4.0 x1 slot and vice versa, with the device operating at the speed of the slower standard.
Thảo luận / Bình luận (0)
Chưa có thảo luận nào cho bài viết này. Hãy gửi bình luận đầu tiên nhé!
Vui lòng Đăng nhập để tham gia thảo luận.